Horizontal offset/ reverse flow build

Blazer · Post by **Blazer** » November 29th, 2011, 3:46 pm

You put alot of thought in that setup, that's some good engineering. :LG:

Gizmo · Post by **Gizmo** » November 29th, 2011, 6:43 pm

WOW! - that's a thing of beauty... I think I'm starting to tear up ...

Post by **Tom_Heath** » November 29th, 2011, 10:30 pm

I was talking smack to frank last night and told him he should have used air cyl's on it. That way it would flip the meat for him.

OMG I really made myseld laugh.

After the laughing at myself and I got to take a close up look at it. Its fantastic.
:LG:

mike · Post by **mike** » November 29th, 2011, 11:04 pm

watched the vid on this and i want one. that is truly a work of art. i myself will have two cranks on mine and will not use a drill i got a couple of HOOTERS girls for that sad that my cranks will be really really low to the ground, ill call my poor design lol

Gizmo · Post by **Gizmo** » November 30th, 2011, 5:42 pm

OH you got that design HAPPENING mike! - see what you started Frank?

k.a.m. · Post by **k.a.m.** » November 30th, 2011, 7:51 pm

Frank, you get the that kicks A$$ award for the year on that set up. There is not enough smilies and emoticons for that on this forum. :LG:

. Congrats my my on a job well done.

YouTube · Post by **Frank_Cox** » November 30th, 2011, 8:27 pm

thanks Kam!

YouTube · Post by **Frank_Cox** » December 1st, 2011, 6:47 pm

Early Christmas today! Got the fresh water tank,the gray water tank, the water pump, and 2 really nice toolboxes for storing gear. The tanks are both 20 gallons each. The gray water tank will be installed under the trailer inside the frame and the fresh water tank will be on too of the trailer deck. It will be closed in with metal and have an access door to get to it. The toolboxes will then be installed over it stacked on too of raconteur. The pump will be installed under the sink. Now I gotta find a sink lol.

Sent using Forum Runner. Try it out for Android or iPhone IOS

The Czar · Post by **The Czar** » December 1st, 2011, 8:52 pm

Nice...real nice....can't wait to put that in!!!

Gizmo · Post by **Gizmo** » December 1st, 2011, 8:55 pm

Grab yourself some stainless and make your own sink in the shape of pig!

Post by **Tom_Heath** » December 1st, 2011, 8:57 pm

Oh ya! !!! A pig sink would sure pimp out the railer.....

Sent from my GT-P7510 using Tapatalk

Gizmo · Post by **Gizmo** » December 1st, 2011, 8:58 pm

Would sure what...?

YouTube · Post by **Frank_Cox** » December 1st, 2011, 8:59 pm

haha, looks like tom had another keyboard misfire

Post by **Tom_Heath** » December 2nd, 2011, 8:50 pm

Damn tablet fell off my lap and almost hit the floor but I saved it. bad news was that i hit the send key LOL

YouTube · Post by **Frank_Cox** » December 2nd, 2011, 8:54 pm

hahaha!

Gizmo · Post by **Gizmo** » December 2nd, 2011, 10:38 pm

Never met you in person Tom but the more you type the funnier lookin you get ...

YouTube · Post by **Frank_Cox** » December 2nd, 2011, 11:10 pm

I got the handwheel and the sprockets installed tonight. still got some tuning to do to them and also build a guard for the chain etc.

More to come

YouTube · Post by **Frank_Cox** » December 2nd, 2011, 11:24 pm

ok, here's some more pics...

Gizmo · Post by **Gizmo** » December 3rd, 2011, 6:57 am

That's some nice lookin work Frank!

Gizmo · Post by **Gizmo** » December 3rd, 2011, 6:58 am

I'd like to put a control wheel on my next project - suggestions on where I might find scrap ones? - Boiler valves? Draw bridges? Navy subs? Bank vaults?

k.a.m. · Post by **k.a.m.** » December 3rd, 2011, 9:23 am

Frank, this is getting more tricked by the day.

What will be the gear reduction amount?

Post by **Tom_Heath** » December 3rd, 2011, 10:40 pm

Wheeeewww.....there for a second I thought I saw some chrome!!! LOL

EK, I try to kick back and have a good time. I stress way plenty at work so when I get to the computer I try to let loose. Making the move from dumb labor to management was a big jump. Its alot to take on all at once, running my guys isnt to bad and the paper work isnt to bad but taking care of the IFTA paper work is a chore. Then having to fill in when someone is gone just puts the icing on the cake.

Since I went in the office my time here has been limited and my build time has been even less. Its getting better though.

Frank. I think we need to remame this thread to Pimp My Smoker!!!!!!

The chain drive is looking really good, but I still think air cylinders would have topped it off. LOL

YouTube · Post by **Frank_Cox** » December 3rd, 2011, 10:42 pm

@kam... it is a 5.5:1 ratio.

stay tuned... I'm gettin ready to post today's progress

Post by **Tom_Heath** » December 3rd, 2011, 10:44 pm

Any chance you can incorporate this into the logo?

YouTube · Post by **Frank_Cox** » December 3rd, 2011, 10:59 pm

@ tom- that's disturbing LOL

anyway, on to the progress. spent the whole morning cleanin the shop and then busted out some work on the smoker. here's some pics. mostly worked on the gray water tank and the cooking grate for the grill.

: drillin the pilot hole

: using a hole saw to mark the spot for me to cut with the plasma cutter

: the marked out hole

: cutting the holes

: the 2 holes we need for the sink drain and the tank vent

more to follow in a minute

SmokerBuilder.com

Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build

Re: Horizontal offset/ reverse flow build