I have to agree with the others and vote for the propane tank. You will not regret having the thicker metal when it comes to heat control. Are you planning on mounting this on a trailer? You will find tons of different builds on this site. Take a look around and see what features you want to put on your own build. I also would suggest visiting http://www.smokerplans.net and investing in a set of plans for your build. It really takes the guess work out of designing the most important parts of your cooker.
Actually, now that this had been decided, I'm ordering the plans from the site once I have the tank in the yard ..hopefully in a few days...that was never a question...what I don't know about smokers could fill , well a big smoker.
I don't mind the work, I just insist on quality and performance and at least I'm smart enough to let the experts tell me how to get it done the right way . As for the trailer, yes. It may not travel more and a few hundred feet from the house but not having the option would just be crazy....
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
I have another question....a little knowledge is a dangerous thing...
I have been reading like nut and see several questions in the making of this RF smoker. I really will prefer to find a smaller propane tank to use but I have to admit, handling big weight is going to be a problem here at my house...just not really equipped for it. Keep this in mind though....I am mighty #%^& determined.
As mentioned, a friend dropped off a 275 oval oil tank that is in nearly new condition. So new I should replace my 550 with it... However it is here and clean. I understand the need for steady temperatures with little deviation.
Is it at all practical to build using this oil tank but wrapping the shell with another steel layer and insulation in between? I saw the box on the forum made with concrete nail stand offs to keep the batting in place... Any thoughts on this or is it just better to bite the bullet and get the propane tank. I know the extra work involved and the higher build cost in wrapping the oval tank with more steel...is the trade off crazy thinking?
FYI, not afraid of hard work, just getting older trying to do it...one of those things where your 60 year old brain tells your body it thinks its 25....until you actually do it.
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
I would say its not just a matter of extra work or cost but in then end the propane tank will make you a happier camper and you will get several lifetimes of use out of it...
If you can't fix it by sheer force or cursing......then it can't be fixed.....
Started the topic clearly saying..." I am going to do this only once so I want to get it right". With All of the suggestions to go with the thicker propane tank, my first build is going to be the 275 oil tank that will be given back to the friend who gave it to me originally to use.
The man has become a nice friend,helpful and found me a set of wheels for my monster log splitter. I'll gain the experience and hell get a great smoker not as actively used as it should be, but he'll enjoy the heck out of it...
The plans were downloaded only a few minutes ago and I'm ready to start drawing on the tank tomorrow. Steel shop will be happy to see me on Monday. Any thought before diving in? Please just say so.
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
In the 25 minutes I am reading the plans, I can see the dimensional stuff is pretty easy but I am finding a good chance, I'll be a bit confused on assembly having never seen one before. Might there be a source of an oil tank oval smoker photograph with some of the details revealed? My next best guess is to call Frank!
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
Hi Frank,
Bought your plans and placed the tank on its back to measure and cut. I have a few questions on the door details and while I will gladly call, I hate to bother you and be a pest. The door cut was very fast. Used a sawzall with metal blade and it took maybe 25 minutes to go around the entire perimeter. Turns out,my friend left the tank with about 15 gallons of oil still in it. After I drain and mop it up, is a good burn the best way to clear it out or should it be "washed" or glass beaded, etc?
If your prefer that I call , I will but here is a brief preview of my questions
1. Is it a good idea to tack a 1" flat stock to all of the edges of the doors with an overlap like the center seam? Seal or cosmetics?
2. The door lock assembly is something I just cannot visualize in my mind. Do they slide left to right or drop in up and down?
3. Regarding the fire box... Am I creating a slide adjustment for the damper or am I not understanding the print out?
4. The fire box door detail is messing with me also...is the angle iron making the door have a lip on it that goes into the fire box opening when the door is closed?
5. This particular oil tank has formed sides, it is not flat...you can see a little view in the top photo below. I assume it is acceptable to weld a 1" angle iron to the top edge of the throat on the firebox/tank radius cut to act as a support for assembly when getting it ready to weld and likely remain a permanent part of the smoker?
6. What is the purpose of the baffle plate cut outs? Is it to fire the rotisserie? I am thinking I would rather just weld a plate in from the right end firebox side to the other end with the right amount a space at the left side ??? After all it will just simply rest on the curvature of the tank as I see it? That would be an easy fit and weld , unless there is some great reason to keep the baffle cut outs In the design? What is the baffle plate length with the right side welded over the top of the fire box throat to the open left side? By the way,I don't think I am using a rotisserie. Using the oil tank wasn't my first choice so I figured I'll build this and give it back to the friend who gave me the tank, he gets a free smoker and I gain a boatload of knowledge for my propane tank smoker next in line. The rotisserie is still not decided on....but to guess I need to plan either way
7. I don't see the racks for the interior of the smoker in the print. I assume I can weld in a set of sliding tracks and a center support to make a set of 4 slide out shelves for the inside or just two full length ones? Of course I only assume. After looking at so many pictures on the site, this was my thinking
8. What material is best to use for the 6" id smoke stack nearly 3' tall?
Thanks for all of the help.....Al
Last edited by Puff on September 8th, 2013, 11:07 pm, edited 9 times in total.
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
Here are the new developments on my 1st smoker build. I have asked 20 other questions all over the forum and bought my plans a few days ago. I had a friend drop off a 275 oil tank that was only a few years old knowing I was planning to build a smoker. He told me since it was in near new condition, he could not just cut it up as trash. So...
My plan was to go with the propane tank. Bt he was great to think of me and since I am new at this, I will follow Franks plans and make a smoker....to my friends surprise, next year when I get the propane tank finished, he will get this one back...ready to enjoy after I use it a bit ;)
I will continually update you all here with a few pictures. These are just the first cuts but tomorrow is my first visit to the steel store.
Oil tank on its side
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
The last picture IS upside down...no idea how that happens. There was also about 19 gallons of oil left in the tank but it was loaded with sludge so I won't be pouring it in my tank
Adding a trailer to this thing... Even with the cut out parts, it weighs too much to move without any kind of equipment. For me, it's either a tractor with no loader or pto or my pickup and a chain!
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life