150 Gallon Reverse Flow Smoker Build

Gizmo · Post by **Gizmo** » March 6th, 2014, 6:17 am

Good looking work! That is nice insulation to work with - I used it on Edgar and a half inch really helped.

Clover Ridge Smokers · Post by **Clover Ridge Smokers** » March 6th, 2014, 7:42 am

wsiddoway · Post by **wsiddoway** » March 6th, 2014, 9:37 am

where did you get your insulation?

Destroyr350 · Post by **Destroyr350** » March 6th, 2014, 11:14 am

wsiddoway wrote:where did you get your insulation?

I have a Harbinson Walker Refractory office local so I go straight to them. They will ship to you though.

http://www.hwr.com

Destroyr350 · Post by **Destroyr350** » March 6th, 2014, 5:06 pm

Todays progress: I finally decided on a chimney design and started my triple stack setup.

I also finished up the firebox door and mounted it to the firebox.

Tomorrow I should have time to finish up the chimney setup.

Getting close

CrazyD · Post by **CrazyD** » March 6th, 2014, 5:11 pm

looks great!

SmokinFF · Post by **SmokinFF** » March 6th, 2014, 7:23 pm

Almost time to make that thin blue line.

bluecatfish · Post by **bluecatfish** » March 6th, 2014, 7:40 pm

Anxious to see pictures with the 3 stacks attached.

Destroyr350 · Post by **Destroyr350** » March 6th, 2014, 8:36 pm

bluecatfish wrote:
Anxious to see pictures with the 3 stacks attached.

I'm anxious to see it myself. I don't think I have ever seen a smoker with triple stacks like that, kinda why I'm trying it.

Destroyr350 · Post by **Destroyr350** » March 8th, 2014, 12:53 pm

Chimneys mounted. Next I have to put some wheels on this and do some final structural welds. I decided to make a patio unit so I can store it in my garage.

bluecatfish · Post by **bluecatfish** » March 8th, 2014, 5:50 pm

That's the picture I've been waiting to see. Being mounted staggered looks neat and you will have smoke coming from all levels in the CC. Let's make the smoke roll!

Clover Ridge Smokers · Post by **Clover Ridge Smokers** » March 8th, 2014, 7:37 pm

bstory · Post by **bstory** » March 9th, 2014, 11:32 am

Those stacks are sweet, when making stacks like that do you use the same volume if you were using one long one and divide it by 3?

Destroyr350 · Post by **Destroyr350** » March 9th, 2014, 3:36 pm

bstory wrote:Those stacks are sweet, when making stacks like that do you use the same volume if you were using one long one and divide it by 3?

Yes, These 3 total a little under 700 cubic inch. Recommended is 600 cubic inch

Clover Ridge Smokers · Post by **Clover Ridge Smokers** » March 10th, 2014, 7:32 am

Grabber70Mach · Post by **Grabber70Mach** » March 10th, 2014, 8:16 am

Nice looking build.

Sent from my VS980 4G using Tapatalk

vizion · Post by **vizion** » March 10th, 2014, 12:04 pm

Really liking the build.. Can't wait to see her all painted up and bellowing smoke.. Nice job.

capt j-rod · Post by **capt j-rod** » March 10th, 2014, 1:17 pm

Does it fit out the door? I won't answer why I know to ask that question!

dwwantasmoker · Post by **dwwantasmoker** » March 10th, 2014, 6:28 pm

Destroyr350 · Post by **Destroyr350** » March 12th, 2014, 6:45 pm

Yes, It fits out the door, I measured several times while I planned this!!! Over the past few days I put some wheels on it and rolled it out for a little test. Right as I was about to fire it up I realized I didn't insulate the firebox yet. Nothing was sealed and there still are no dampers or air controls yet but it heated up to 250 and I got it to stay there without a problem. The chimneys draw fine, that was my only concern. Still have to weld in supports but this will give you an idea.

trekinaway · Post by **trekinaway** » March 15th, 2014, 7:04 pm

Love it

Smokeone · Post by **Smokeone** » March 16th, 2014, 1:00 pm

Post by **Rodcrafter** » March 17th, 2014, 5:57 am

bluecatfish · Post by **bluecatfish** » March 17th, 2014, 11:33 am

Gizmo · Post by **Gizmo** » March 21st, 2014, 4:47 am

THat looks like it'll work!

SmokerBuilder.com

150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build

Re: 150 Gallon Reverse Flow Smoker Build