There was nothing to do today. So after the fourth episode of BBQ Pitmasters, I took Frank’s drawings and tried to calculate the materials I would need to order to complete the entire smoker. And while this is no means an exact measurement, I think it comes close enough for me to go and order my stuff on Monday. This will get it completed except for the shelves and rebar…. I hope
For anyone with the plans who may benefit from this information, it is listed below. Again this is what I came up with and will allow for some small scrap.
50 feet of 2x2 16 gauge
10 feet 1 ¾x 1 3/4 14 gauge
1 4’x4’x ¼” plate
1 ½ sheets of aluminum tread plate 1/16” 4’x8’
20 feet of guide rail material for shelves
1 ¼ sheets of 18 gauge 4’x8’
Feel free to dispute these calculations…despite my sheer genius , I did need to take Geometry twice
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
That's a good question CR. I get free time at irregular intervals and there's always something else that needs to get done. I would surely hope to finish before November. Especially that I have a rough idea of the materials I need to have on hand. Monday I am just heading to the steel place and picking up everything on this list, it'll just be in the pile...ready and waiting.
Additionally, the thinner materials makes it so much easier to cut. So this will make a big difference in boredom cutting delays. The biggest problem I had on the oil tank was, with a free hour to work on it, I would be hunched over a sawhorse with a tiny cutter going no where fast. Then get cleaned up ( you know how that mill scale just greases you up) to get back into the real world. "Ok, I'll just not bother doing that today."
But, who knows...the cold does not really bother me. Heat just rips me apart. Easier to warm up then cool down. I'll keep all updates and photos in this thread.
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
Hey Pete, they only pre cut in Williamstown. In Wall, you get what you see in stock! They have cut some 20 footers for me but only adding " well, you're here a lot...ok". Not inspiring for a complete order. Beside they have only a chop saw. I should call and price it out. Could be worth the trip over.
The plan lists the McMaster-Carr prt numbers so that will be easy to just get those pieces
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
Sometimes the exposed edges look so much better from a shear than a zip disc that the time savings isn't the only reason for ordering pre-cuts where possible…. so you burn a day going after it versus an extra week cutting parts…. tough call ….
And on the eighth day God created barbecue …. because he DOES love us and he wants us to be happy.
Current smokers: Egor (trailered RF) and Easybake (tabletop pellet drive)
sounds great Puff! I will tell ya the McMaster Carr part numbers are for reference only. There are some other parts you can use to save some money! gimmie a call monday afternoon and I'll help ya figure those out.
So it's July 7.... I went over to the steel store and bought all of the square tubing. 60 feet of 2x2" in 12' lengths and two 1 3/4" square tubes 10' each. Another 10 lbs of 3/32 7018 rod and a box of 4.5" cutting wheels. I think this one is going to be easier with regards to cutting and preparing the metal. It is all so much lighter gauge and weight than the trailer and tank.
If it weren't so hot and steamy out, I'd start tonight but I'll start after work ....maybe. Weather depending. Any one else starting one of these?
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
I am sure I will either have a few questions or come across something I am NOT very clear on...if you might be zipping along, I have another source of information. It's a bit of a security blanket ? I already seem to find a misunderstanding of the firebox connection and the part that leads to the CC.
EDIT: just had a great telephone conversation with Frank at HQ. He cleared a few points for me, made some simplifying suggestions and saved me several hundred bucks towards the end results ....Great guy to have around
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
Sent the cut list for the chute assembly to the supply house today. My quote from the 1/2" thick bottom .....to the door up top including the three flanges and all of the 1/4" plates is about $300.00. There is no way I can reasonably cut the 1/2" stuff and it will be a bit easier to have those flanges nicely cut, clean and SQUARE. Does this seem over the top or...should I just order it Monday?
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
Ordered it anyway.... Will be ready for Friday pickup . I guess it will be nice just aligning it up and welding it together. Should have the chute done Saturday
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
Thanks Frank, I would just hate to hear...." What !, I can get the same thing for $200.00 ". Bringing home the sheet metal and decided to go with the aluminum tread plate for the door when I pick up the pre-cut stuff , just to give it some contrast.
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life
Made progress today. Picked up a 4 x 10 18gauge sheet some more angle iron, flat iron and box tubing... I can only say that I find this style of smoker really nice to build. Cutting the 4 x 10 sheet took less than an hour to get all the pieces I needed for the inside of the cabinet. Cutting it with the grinder moves at about 1 in. per second for the first pass, scoring a line. A second pass through that line cuts the material.
On the quarter inch plate I had used for the firebox on my trailered smoker, it took me almost all of November to get the pieces I needed. My steel for the charcoal chute is ready to be picked up so things will be moving along so much quicker.
Had a few questions for Frank and received really good answers. When he writes messages, you just cannot get him to stop ;) ,his lengthy answer was... "Get the Miller" and " no, strap is always better" . To be fair, I just asked him to pick A or B and my Miller 211 will be here on Tuesday.
I figured it will be much easier to weld the thinner materials with a decent MIG.
Make no mistake, there ain't no powder in this Puff ! And... I'm not really a crazy person but I play one in real life