Hey neon. I'll throw some ideas at ya. 1/4" material great for your build. I've used 3/16" and have had good luck. 18" dia. is kinda small in my opinion,maybe larger dia. and shorter length? Rectangular cc could be an option, easier to work with. Definetly put air vents in your fb. You will find some folks like to put one on each side and low. Check out the pit calculator on this site it will help. You will find this site to be a great resource for building and cooking. Good luck.
Yep I'd go at least 20" deep. Gizmo used to recommend going to the meat department with a tape measure to make sure the items you want to cook will fit. In my opinion 1/4" is a minimum thickness. Making the whole thing out of flat plate, is a very good idea. That would allow you to have cabinet doors.
Making memories.
Current Smokers: Backyard RF Offset and Hybrid RF Offset trailer rig with Cowboy cooker and fish fryer, always room for more........
For a first build I would recommend checking out Frank and his smoker plans. Even if you end up designing your own, it is money well spend on proven ideas.
Thanks a lot for the tips fellas! I think I'll change up my blueprints and make it a rectangular CC. Would also save me some bucks as I wouldn't have to commission the cylinder from an outside entity.
Well, I'll get to it! Once I've got some progress I'll post up some pics.
Welcome aboard!
1/4 " plate definitely and yes,18" would be too small.At 20" you would have enough space for a smaller 2nd rack on top of the 1st,but if you go rectangle,that would be the ticket!Opens soooo many choices....
Good luck and keep us posted.
(BTW-keep a the look out for the Czar.He's a stickler for .His motto is,"no pictures,it never happened,LOL)
Finally getting rolling. Finished up some smoker blueprints in Sketchup, got my materials at the local steel yard and started welding this weekend...I'll upload photos from my phone in the following post of my progress (it doesn't seem to be working from my computer).
Anywho, I've been digging through the forums tonight for more inspiration and tips .. Mack is indeed incredible, I am certainly not at that level yet!
Nonetheless, I still have a few questions on my build for y'all, if it isn't too much of a bother...
just to clarify, I'm building a rectangular smoker. 36x20x20 with a FB 15.75x15.75x16...here are my queries
1. Baffle Plate. I am not building a reverse flow, just a simple offset. How far out from my CC wall should the BP extend? or, how long should it be? Should the BP be only as wide as the throat? Or is it better that it go from wall to wall in width?
And what about the angle of the BP, I was planning on having it at about a 60 degree angle with the throat. Is perpendicular better? [throat is 4x8 rectangle]
2. grease valve/drain. I will of course have a hole on the bottom of my CC for grease drip. Is it necessary for me to tilt the bottom of the CC in some way, in order to drive the grease towards the drain? Or ok if I leave it flat and the grease will find it's way out?
3. Door. Is a big door generally the better call? I drew up a door that was 22" in my blueprints. leaving about 7" on each side of the door. Will I be regretting this small a door? I'm putting in 2 grates, so 22" should get those in and out fine.
4. FB intake. pit calc recommends a FB intake area of about 12". I was thinking of install 4 horizontal slits of 1x3 . 2 on each side of the FB. or would two 2x3 slits work just as good. I figure no need to put a vent on the front of the FB as I could just crack to door for the same effect. This is probably a dumb question, but I second guess myself about everything!
I don't think I'll put a basket in my FB for now, but I can always add that in the future.
Well, that's all I got. Thank y'all so much for the help! I'd be up in smoke without you ... and not the blue kind!
FB is a little small. Should be more like 18 x 17 x 16. Shoot for ~105% differential. There is no BP in a standard offset smoker, just tuning plates. See pic.
As for the height of the tuning plates, you need ~40 sq. in. Throat so if you leave a 2" high opening x 20" long you'll have enough. Leave a 1" grease dam at the very bottom of the throat and install your drain there. The top of the FB is at the top of the throat opening. I would keep the height of the tuning plate rails just above that. Have your lower cooking grate about 4-5" above the tuning plates. I would make the door/s as wide as I could and the grates as well. FB intakes could be bigger because you can always shut them down. It's usually easier to make 2 larger ones than 4. You'll need something to support the wood and coals or you won't get good combustion.
If it's tourist season, how come I can't shoot 'em?
Thanks so much for the detailed reply. And thanks a ton for checking my numbers. Man, I'm an idiot. I checked those numbers a few times, but didn't set it to square rectangular cc (I was originally building a cylinder), and thus calculated my FB to that. Really kicking myself !!!
As per the tuning plates, I am afraid I'm on a bit of a tight budget and don't have the bucks to build out the tuning plates now (though luckily I have enough drop from the other parts to extend the FB). I was just going to leave the CC open and build a baffle over the throat to avoid a major hotspot on that side of the CC. Does that make sense? In this case, I return to my original questions about the drain and whether I need to tilt the bottom of the CC, and also the size and angle of the baffle.
Thanks again for the assistance
At least mount some angle for the tuning plates to rest on, even if you have to add them later. You will want to add them later. Tilting the smoker can change how it cooks. Usually the FB end is lower so stuff flows to the front of the throat where the drain is. No need for an angled baffle. You'll have plenty of room to keep the FB well below the cooking grate. Your first tuning plate could be 8 or 10" but you could make it bigger if you have more steel.
If it's tourist season, how come I can't shoot 'em?
Pete,
Thank you so much for the advice. I really appreciate it! I'll do exactly that and install a shelf for the tuning plates to rest on. In the future. I probably have enough steel for one. I'll aim to make it about that size. How high above the throat should I set the tuning plates? Or should they be flush with the top of the throat?
It can be the same height as the throat or a few inches higher. The main thing is to keep them in the 4''-6'' range from the bottom rack, I try to build my RF with a 4'' gap.