Just my 2 cents, but I believe Frank has this exact size smoker on his website. It lays out all the dimensions and is a proven design so will save you a lot of time from having to redo or recut pieces. It pretty much lays out each piece and gives you the overall order to best assemble it. In my opinion, it was worth every cent and good for reference/piece of mind even if you choose not to follow it.
with that said, you can push the stack all the way to the end. You will need to leave room for the door to swing. Remember you will most likely have a piece of 2 inch strap to seal the edges of the door so calculate in the overhang portion as it increases door width.
I would make bottom door cutout a bit lower than 3:00. It will allow you a little wiggle room and prevent you from smashing your fingers if you ever slam the rach back in and grab the rack by bottom edge.
I see no problem aligning the rack with the baffle plate gap. It will probably create a bit of a hot spot on that side but, if so, push your food over a few inches. I think my bp runs about 2 inches longer than my rack....I can measure in the morning if you want.
I build my racks to start at the end of my BP and I leave the same amount of spacing on the FB end (I'm a little OCD) I usually run my stack out the end of the CC over the FB if I'm not building a WC but you can squeeze it out the top. I wouldn't put the stack above my racks to keep any drippings off of the food. If you make your bottom door cut 1'' below 3 oclock it'll let your bottom rack be as deep as possible, the top cut is fine. It looks like your BP is 6'' below your bottom rack, that is about the max distance that you'll want to be. I would try to get it a little closer and take advantage of the radiant heat from the BP. I like to be in the 3''-4'' range if possible but that's just my preference. The last FB door I done I used 1/2'' plate cut to fit the door opening and framed it with 1/4''x1'' flat bar.
If I move my stack over the firebox, I think I read that I don't count the bend but still keep my stack length the same from the top of the pit. I'll see if I can find that link or let me know if I'm wrong.
Big T, I like the idea of keeping the spacing the same on both ends. If I lower the rack to 4 inches above the BP does it looks like my door opening will have an almost 4 o'clock lower opening (new line in the drawing) is that around where your door openings are since your lower rack is closer to the BP?
It's a smaller pit but I want to add a counterweight so I don't think I'll have any problem with the door weight.
For the FB door, 18 inches isn't a whole lot to work with so I think I've talked myself into making the whole thing the door.
I would keep the lower rack at 3:00 and raise the FB. Use the same cut-out for the throat but just move it up so you'll have a border around the bottom of the CC.
If it's tourist season, how come I can't shoot 'em?
This is a great sized smoker. You are doing a good job on the calculations and the rest is really personal preference. I really like combining what BigT said and what Pete said that is lower the 3 o'clock cut by 1" allowing the main rack to be as large as possible being in the center of the pipe. Then if you want to raise the throat cut don't change it just move it and the FB up. But looking at your drawing it looks like it may be closer than 6" if you just lower the bottom rack the 1 inch. You are also correct about the stack length only count the portion that is above the CC.
jm2cw
Making memories!
Current Smokers: Backyard RF Offset and Hybrid RF Offset trailer rig with Cowboy cooker and fish fryer, always room for more........
A word of warning. I am a newby and have never build nor cooked on a real smoker. So discount my opinions appropriately. There are people on this sight that have great knowledge and experience. Listen to them. They have helped me tremendously. That being said here are a few of my observations.
You might consider cutting the top door seam a bit past 12:00 (on the backside of top dead center. Cover the seam with flat bar/flange welded to the CC door. The thought is that rain water would run downhill away from the top seam. If you cut it at 11:00 (on the door side of TDC), The flange may not protect the seam. Rain water would run towards the top seam and into the CC.
Are you using the inside dimensions for the pit calculator? Might not make much of a difference. The inside diameter of your CC is probably 23.5".
You probably don't need a counterweigh on the door. I'm building the same size pit. The door is not too heavy, but it is a personal preference thing.
made some changes to my design based on your recomendations. Stack to the end and raising the FB.
That is making me raise my BP but no big deal. I reversed/caressed the calculator to figure my length across the CC and it's giving me a width of just over 22.5" at 8 inches high. That should give me plenty of assistance from the BP and cooking.
Here is what I'm looking at for the design and the numbers based on the changes.
I think the pictures match the calculation 100% now and the Diagonal line across the CC is where the Door will be around 11ish and possibly 1 to 1 1/2 inches below 3o'clock.
Moved the FB up, it had been only 4 inches from the bottom of the CC, it is now 8 inches high with my Throat now an equal 2 5/8 opening across the top of the FB.
updates #'s and images so hopefully they can be seen.
Attachments
Pit v3
Pit #'s v3
Last edited by Higee on November 7th, 2016, 10:25 pm, edited 1 time in total.
And on the eighth day God created barbecue …. because he DOES love us and he wants us to be happy.
Current smokers: Egor (trailered RF) and Easybake (tabletop pellet drive)